Cantilever snap fits are one of our favourite features to design. A bit of plastic bends out of the way, clicks home, and two parts are held together with no screw, no glue and no extra line item on the bill of materials. Done well, it feels wonderful in the hand. Done badly, it snaps off on the second assembly.

The maths behind them is real and nicely worked out. But in day-to-day design, ratios of thickness are often enough. This article is the ratio version, plus the part the textbooks tend to skip: which way the hook faces, because that decides how the mold is built. Everything here is a rounded rule of thumb, not a guarantee.

Anatomy of a snap

Five names are worth learning.

  • Beam: the flexible arm that bends during assembly.
  • Root: where the beam meets the wall. This is where it bends most and where it breaks.
  • Hook: the small catch at the tip of the beam.
  • Insertion face: the ramp on the hook that meets the mating part first. It makes assembly easy.
  • Retention face: the back of the hook that catches and holds. Its angle sets how hard the joint is to undo.

The depth of the hook, how far it hangs over the mating part, is called the undercut. The beam must bend at least that far to get past.

Anatomy of a cantilever snap fit A beam of length L and root thickness t leaves the wall at the root, which has a root radius of about half t. The beam tapers to a tip about half t thick and ends in a hook. The hook has a sloped insertion (lead-in) face and a retention face that catches the edge of the mating part. The hook depth is the undercut. Root radius ≈ ½ t Beam length L ≈ 5–10 × t Beam Tip thickness ≈ ½ t (taper) Hook depth (undercut) Hook Insertion (lead-in) face angle ≈ 25–35° from direction of travel Retention face angle ≈ 90° (permanent) or 30–45° (releasable) Root thickness t Mating part its edge
Anatomy of a cantilever snap fit, side view: the beam bends at the root, and the hook at its tip has an insertion (lead-in) face and a retention face.

Beam length versus thickness

Think of length as a multiple of the thickness at the root. Our rule of thumb is a length of about 5 to 10 times the root thickness.

  • Much shorter, and the beam is stiff. To bend the hook's depth it has to stretch the plastic too far, and it over-strains and cracks.
  • Much longer, and it is floppy. It bends easily but holds weakly, and it can buckle or vibrate loose.

If you cannot fit a long enough beam, do not shrink the hook and hope. Both manuals describe L-shaped and U-shaped snaps, where slots in the wall make the effective beam longer in the same space.

Taper the beam

Make the beam thinner towards the tip, to about half the root thickness. Both manuals suggest roughly this, and it is an approximation, not a magic number.

A straight beam concentrates all the strain at the root while the tip barely works. Tapering shares the strain along the length, so you can bend further for the same stress. It also saves a little material and cycle time.

Deflection of a cantilever snap-fit beam The beam is shown twice. The dashed outline is its start position, straight out from the wall. The solid shape is the deflected position, bent upward at the root so the hook clears the edge of the mating part. The deflection y is marked at the tip. A soft highlight at the root shows where the strain concentrates. Highest strain at the root Deflection y (at least the undercut) Mating part's edge Mating part slides in Start position (dashed) Deflected position (solid) Beam bends away
The beam bending away as the hook rides over the mating part's edge. Dashed is the start position, solid the deflected one, and the strain concentrates at the root.

Hook depth, and what the material allows

How deep the hook can be follows from how far the beam can safely bend, and that depends on the material. The longer the beam relative to its thickness, the deeper the hook it can clear. Each plastic has an allowable strain, which is the stretch it tolerates at the root without damage. Rough, rounded ranges for one-time or occasional assembly:

  • ABS: about 2%
  • PC: about 2 to 4%
  • PC/ABS: about 2%
  • PA (nylon): about 3 to 4% dry, rising to 5 to 6% once it has absorbed moisture
  • POM (acetal): about 4 to 5%
  • PP: about 4 to 5%, and it forgives repeated flexing

Glass-filled grades tolerate far less, often only 1 to 2%, because the fibres make the material stiff and brittle. A beam that was perfectly happy in an unfilled grade can crack the first time in a glass-filled one. Always check your resin's datasheet, since grades within a family differ.

For the curious, the tip deflection a beam can survive grows with the allowable strain times the length squared, divided by the thickness.

The root radius

The root is the most common failure point. A sharp inside corner there concentrates stress and the beam snaps off at the wall.

Give the root a radius of about half the beam thickness. Bigger helps a little more, but a large fillet makes a thick lump where the beam meets the wall, and thick lumps cause sink marks and voids. Half is the compromise we reach for.

Angles, width and force

The two faces of the hook do different jobs.

  • Insertion angle (lead-in): about 25 to 35 degrees from the direction of travel for easy assembly. Steeper, and you push harder; shallower, and the hook grows long.
  • Retention angle: about 90 degrees for a permanent snap that will not come apart, and about 30 to 45 degrees for one that releases when pulled or pushed.

Width scales the force, not the strain. Doubling the width of the beam roughly doubles the force to bend it, but the strain at the root is the same. That is useful: if the joint feels loose, widen the beam. Do not thicken it.

Assembly force is also affected by friction. Slippery materials like POM and nylon assemble more easily than PC or ABS at the same geometry. Rounded edges on a hook act like a gentler lead-in angle.

A permanent snap should still be serviceable, because products come back. Give it a way in: a small release slot, or a gap where a thin tool can reach the hook. Otherwise the repair is a hammer.

A hexagonal LED puck light whose molded housing closes with snap features.

Hook direction and moldability

This is the part we care about most, and it is where experience pays. A hook is an undercut, and an undercut is something the mold cannot normally release from. The standard answer is a slide or a lifter: a moving piece of steel inside the mold. They work, but they cost money, add parts that wear, and can lengthen the tooling schedule.

Often you can design them out. The parting line and the pull direction are the mold shop's decisions, so we simply design with them in mind.

  • Face the hook along the pull direction. A hook that points the way the mold opens, or toward the parting line, can often be formed by the two halves of the mold alone.
  • Form the hook through a window. The classic trick: cut a window (a pass-through) in the wall or base beneath the hook. A steel core comes up through that window and shapes the underside of the hook, then pulls straight out. No slide. The window is also the visible clue on a lot of well-made plastic products.
  • Gang the snaps in one direction. If every snap on the part points the same way, one mold action serves them all. Hooks pointing in opposing directions each need their own mechanism.
  • Know what forces a lifter. A hook facing inward on a closed wall, with nothing beneath it to open up, has nowhere for steel to come from. That is the case that costs you a lifter.
Hook faces the pull direction Side section of a snap hook whose retention face looks along the mold pull direction. A window in the wall beneath the hook lets a steel core come up and shape the hook, then pull straight out, so no slide is needed. Hook faces the pull directionWindow in the wall, no slide Pulldirection window → Steel core Hook faces inward on a closed wall Side section of a snap hook facing inward on a closed wall with nothing beneath it. A slanted lifter, a moving piece of steel inside the mold, has to reach the underside of the hook, because no core can come up from below. Hook faces inwardClosed wall: needs a lifter Pulldirection closed wall Lifter
A hook that faces the pull direction, formed through a window in the wall, needs no slide. A hook facing inward on a closed wall needs a lifter.

Does the window cost anything? A little, in appearance and in stiffness, and sometimes a dust path. If it matters, a small cover or the mating part can hide it. Work this out with the shop early, since they decide the split.

Our advice matches the one from the molds article: give the shop a clean model and your requirements, and let their engineers choose the parting line and how each hook is formed. We have seen a single reorientation of a hook remove a slide entirely, and a single reorientation add one.

If you want the wider picture on moldable features, we cover it in Designing Moldable Parts, and on getting tooling fast in Fast Injection Molds in China.

Common mistakes

  • Sharp root corner. Add a radius of about half the thickness.
  • Beam too short for the hook depth, so it is stiff and over-strained.
  • Glass-filled resin in a snap designed for an unfilled grade.
  • Hook too deep for the material's allowable strain.
  • A hook that faces inward on a closed wall and forces a lifter.

Rules of thumb

Rules of thumb as ratios of the root thickness t The beam of the snap fit with each rule of thumb marked on it: length L about 5 to 10 times t, tip thickness about half t, root radius about half t, insertion angle about 25 to 35 degrees, and retention angle about 90 degrees for a permanent snap or 30 to 45 degrees for a releasable one. t Root radius ≈ ½ t L ≈ 5–10 × t Tip ≈ ½ t (taper) Insertion angle ≈ 25–35° Retention angle ≈ 90° permanent ≈ 30–45° releasable t = root thickness Width scales force, not strain
The rules of thumb as ratios of the root thickness t.
Feature Rule of thumb
Beam length about 5 to 10 times root thickness
Tip thickness about half the root thickness
Root radius about half the thickness
Insertion angle about 25 to 35 degrees
Retention angle, permanent about 90 degrees
Retention angle, releasable about 30 to 45 degrees
Width scales force, not strain
Glass-filled resin allowable strain roughly half of unfilled or less
Hook direction along the pull direction, through a window if needed

Further reading

Please read the real thing, since the theory behind all this is free and public, and it is excellent. Two classics are worth your time:

  • Covestro's Part and Mold Design guide is a long, generous design reference. Its snap-fit chapter descends from Bayer's "Snap-Fit Joints for Plastics - A Design Guide", with worked examples for cantilever, U-shaped, torsion and annular snaps.
  • BASF's "Snap-Fit Design Manual" is a lovely, compact walk through beam theory, tapering, root stress and allowable strain. We could not find an official online copy to link, so we cite it by title only; ask BASF or your resin supplier. BASF also runs a snap-fit calculator if you want a first estimate of forces and deflections.

Working on something like this? Get in touch.